Sikagard® WallCoat ID
Sikagard® WallCoat ID is a coloured, water dispersed two part epoxy resin based coating.
- Good Chemical and mechanical resistance
- Excellent decontamination properties
- Solvent free
- Water dilutable
- Impervious to liquids
- Easy to clean
- Easy to mix and to apply
Usage
- Coloured sealer coat for the wall surfaces of interior rooms.
- For concrete or cementitious substrates.
- Particularly suitable for clean rooms in the electric and pharmaceutical industries.
Advantages
- Good Chemical and mechanical resistance
- Excellent decontamination properties
- Solvent free
- Water dilutable
- Impervious to liquids
- Easy to clean
- Easy to mix and to apply
Packaging
| Part A | 18.72 kg container |
| Part B | 5.28 kg container |
| Part A + B | 24 kg ready to mix unit |
Colour
| Resin - part A | Liquid, coloured |
| Hardener - part B | Liquid, transparent |
Available colour shades: ca. RAL 9003, 9010, 7032, 7035
Other colour shades on request.
Under direct sun radiation there may be some discolouration and colour deviation, this has no influence on the function and performance of the coating.
Product Details
APPROVALS / STANDARDS
Conforms to the requirements for Cleanroom Suitable Materials CSM, Report No. SI 1811-1078 Fraunhofer, Germany :
- Particle emission (CSM classification / VDI 2083 part 17 according to ISO 14644-1)
- Outgassing (CSM classification / VDI 2083 part 17 according to ISO 14644-8)
Composition
Epoxy
Shelf Life
12 months from date of production if stored properly in original, unopened and undamaged sealed packaging.
Storage Conditions
Store in dry conditions at temperatures from +15 °C to +30 °C. Protect from frost.
Density
| Part A | ~1.70 kg/L |
| Part B | ~1.09 kg/L |
| Mixed resin | ~1.47 kg/L |
Solid content by weight
~67 %
Solid content by volume
~51 %
Abrasion Resistance
| 120 mg (CS 10/1000/1000) (14 days, +23 °C) | (DIN 53 109, Taber Abrader Test) |
Temperature Resistance
| Exposure* | Dry heat |
| Permanent | +50 °C |
| Short-term max. 7 days | +80 °C |
| Short-term max. 12 hours | +100 °C |
Short-term moist/wet heat* up to +80 °C where exposure is only occasional (i.e. during steam cleaning etc.)
*With no simultaneous chemical attack.
Chemical Resistance
Resistant to many chemicals. Please ask for a detailed chemical resistance table
Application
Mixing Ratio
Part A : part B = 78 : 22 (by weight)
Ambient Air Temperature
+10 °C min. / +30 °C max.
Relative Air Humidity
75 % r.h. max.
Dew Point
Beware of condensation!
The substrate and uncured floor coating must be at least 3 °C above dew point to reduce the risk of condensation or blooming on the floor finish.
Substrate Temperature
+10 °C min. / +30 °C max.
Substrate Moisture Content
< 6 % pbw moisture content.
Test method: Sika-Tramex meter or CM-measurement.
No rising moisture according to ASTM (Polyethylene-sheet).
Pot Life
| Substrate temperature | Time |
| +10 °C | ~120 min |
| +20 °C | ~90 min |
| +30 °C | ~30 min |
Curing Time
Before applying Sikagard® WallCoat ID on Sikagard® WallCoat ID + 5 % water allow:
| Substrate temperature | Min. waiting time | Max. waiting time |
| +10 °C | 48 hours | 7 days |
| +20 °C | 15 hours | 5 days |
| +30 °C | 10 hours | 3 days |
Before applying Sikagard® WallCoat ID on Sikagard® WallCoat ID allow:
| Substrate temperature | Min. waiting time | Max. waiting time |
| +10 °C | 24 hours | 7 days |
| +20 °C | 12 hours | 5 days |
| +30 °C | 10 hours | 3 days |
Times are approximate and will be affected by changing ambient conditions particularly temperature and relative humidity.
Applied Product Ready for Use
| Substrate temperature | Tack free time | Full cure |
| +10 °C | ~2 days | ~10 days |
| +20 °C | ~15 hours | ~7 days |
| +30 °C | ~10 hours | ~5 days |
Note: Times are approximate and will be affected by changing ambient conditions.
Consumption
| Coating System | Product | Consumption |
| Priming | Sikagard® WallCoat ID + 5 % water | ~140 g/m² |
| Coat | 2–3 × Sikagard® WallCoat ID | 100–150 g/m² per coat |
These figures are theoretical and do not include for any additional material required due to surface porosity, surface colour, surface profile, variations in level and wastage etc.
MIXING
- Prior to mixing stir part A mechanically. When all of part B has been added to part A, mix continuously for 2 minutes until a uniform mix has been achieved.
- To ensure thorough mixing pour materials into another container and mix again to achieve a consistent mix.
- Over mixing must be avoided to minimize air entrainment
MIXING TOOLS
Sikagard® WallCoat ID must be mechanically mixed using an electric power stirrer (300–400 rpm) or other suitable equipment.
APPLICATION
Prior to application, confirm substrate moisture content, relative humidity and dew point.
If > 6 % pbw moisture content, Sikagard®-720 EpoCem® HC may be applied as a T.M.B. (temporary moisture barrier) system.
Primer
Make sure that a continuous, pore free coat covers the substrate. Apply the Sikagard® WallCoat ID + 5 % water by brush or roller.
Wall coating
Apply Sikagard® WallCoat ID by roller.
CLEANING OF TOOLS
Clean all tools and application equipment with water immediately after use. Hardened / cured material can only be mechanically removed.