Product Data Sheet Show all documents
Sikafloor® Marine-120

Sikafloor® Marine-120

Lightweight self-leveling primary deck covering mortar for interior decks

Sikafloor® Marine-120 is a 1-component light weight and self-leveling mortar based on polymer modified cement. Sikafloor® Marine-120 is tested according to FTP Code system and approved according to the IMO Marine Equipment Directives.  

  • Lightweight leveling mortar
  • One component, ready to mix
  • Easily applicable
  • Good leveling properties
  • Applicable up to 30 mm
  • Can be pumped
 
Product Data Sheet Show all documents

PRODUCT BENEFITS

  • Lightweight leveling mortar
  • One component, ready to mix
  • Easily applicable
  • Good leveling properties
  • Applicable up to 30 mm
  • Can be pumped
 

Usage

Sikafloor® Marine-120  is applied on interior decks, to level the surface prior to the application of deck finishing materials such as: carpets, tiles, parquet, rubber and vinyl. It is suitable for application in dry and wet accommodation areas exept for galleys. This product is suitable for experienced professional users only. Test with actual substrates and conditions have to be performed to ensure adhesion and material compatibility.  

Packaging

Bag

16 kg

Product Details

Typical Product Data
Chemical Base

Polymer modified cement mortar

Color

Grey

Cure Mechanism

Hydraulic

Density

mixed

cured

1.12 kg/l

0.9 kg/l

Mixing Ratio

per 16 kg bag

5.9 ─ 6.5 liters

Substrate Temperature

5 ─ 30 °C

Application Thickness

3 ─ 30 mm A

Coverage

per 16 kg bag at layer thickness 1 mm

17 m2

Working Time (CQP599-9)

20 minutes A

Ready to Walk on (CQP600-3)

depending on humidity and ventilation

12 hours A

Compressive Strength (CQP599-2)

9 MPa B

Flexural Strength (CQP599-1)

3.4 MPa B

Modulus of Elasticity in Compression (CQP599-6 / EN 13412)

2.5 GPa B

Linear Shrinkage (CQP599-5)

0.03 % B

Shelf Life

12 months C

CQP = Corporate Quality Procedure

A) 23 °C / 50 % r. h.

B) after 28 days

C) stored in a dry, cool place below 25 °C
Technical Information

CURE MECHANISM

Sikafloor® Marine-120 cures by way of hydraulic curing.

Application

Application Information

Surface Preparation

For leveling applications, the surface has to be clean, free from dust, grease, oils and other substances, which may impair adhesion. Rust has to be removed with a steel brush or other appropriate means, followed by vacuum cleaning.
The surface has to be primed with Sikafloor® Marine Primer C using a long hair roller. After drying of the primer Sikafloor® Marine-120 may be applied.
Sikafloor® Marine-120 applications on aluminum or zinc rich shop primer coated decks, require a tie coat of SikaCor® ZP Primer or another suitable tie coat prior the priming step with Sikafloor® Marine Primer C.

Application

Apply the mortar with a steel board or a straight edge.
Sikafloor® Marine-120 can also be applied by pinrake. Sikafloor® Marine-120 has to be applied within 20 minutes after mixing. At temperatures above 30 °C the open time will be reduced to 10 minutes or less. If applied in thickness less than 3 mm the self-levelling capability will be reduced.
For advice on selecting and setting up a suitable pump system, contact the System Engineering Department of Sika Industry.

 

Curing

After application, the finished areas have to be protected against direct heat (e.g. cutting or welding from beneath), sunlight and draught during the curing process for at least 12 hours.
Before Sikafloor® Marine-120 is covered with dense materials such as vinyl, etc., ensure that the remaining moisture level is below 4 %.
Test procedure to determine the dryness (according ASTM D 4263): put a PE-plastic foil 1 m x 1 m on the surface of the applied mortar floor, tape the perimeter and leave for one day. The curing is complete if there is no water condensation on the foil or a visible color difference between covered and uncovered surface.

Removal

Excess material can best be re-moved before curing with a trowel wipe.

Fresh Sikafloor® Marine-120 may be removed from tools and equipment with water. Once cured, the material can only be removed mechanically.

Exposed hands and skin should be washed immediately with water. Use a suitable skin protection hand cream.

Application Limits

For applications on slooping surfaces > 1 % contact the Technical Department of Sika Industry.

Documents