Sikafloor® MultiDur EB-39
Sikafloor® MultiDur EB-39 is a slip resistant, tough-elastic, coloured epoxy covering with high chemical resistance for flooring applications
- High chemical resistance
- Crack-bridging
- Liquid proof
Usage
Crack-bridging and chemically resistant coating for concrete and screed surfaces in bund areas for the protection against water contaminating liquids (contact Sika technical service for specific information)Advantages
- High chemical resistance
- Crack-bridging
- Liquid proof
Packaging
Please refer to the individual Product Data Sheets
Colour
Available in various colour shades.
Appearance
Slip resistant, gloss finish
System Details
APPROVALS / STANDARDS
- Slip resistance certificate according to DIN 51130, class R12 V4, Report No.12 7465-S/15, MPI Institute, June 2015, Germany
- Slip resistance certificate according to DIN 51130, class R11 V4, Report No.020108-13-22, Roxeler Institute, October 2013, Germany
System Structure
Sikafloor® MultiDur EB-39 system (~ 2–3 mm)
| 1. Primer | Sikafloor®-161 HC |
| 2. Wearing coat & broadcast | Sikafloor®-390 N & broadcast with silicon carbide 0.5–1.0 mm or quartz sand 0.4–0.7 mm |
| 3. Top coat | Sikafloor®-390 N + 5 % by weight Thinner C |
Composition
Epoxy
Nominal Thickness
~2.0–3.0 mm
Shelf Life
Please refer to the individual Product Data Sheets
Storage Conditions
Please refer to the individual Product Data Sheets
Chemical Resistance
Refer to the chemical resistance of Sikafloor®-390 N. Contact Sika technical service for specific information.
Temperature Resistance
| Exposure* | Dry heat |
| Permanent | +50 °C |
| Short-term max. 7 d | +80 °C |
| Short-term max. 12 h | +100 °C |
Short-term moist/wet heat* up to +80 °C where exposure is only occasional (i.e. during steam cleaning etc.)
*No simultaneous chemical and mechanical exposure.
Skid / Slip Resistance
| R12 V4 | (DIN 51130) |
| R11 V4 | (DIN 51130) |
Application
Product Temperature
Please refer to the individual Product Data Sheet
Ambient Air Temperature
+10 °C min. / +30 °C max.
Relative Air Humidity
80 % r.h. max.
Dew Point
Beware of condensation!
The substrate and uncured floor must be at least 3 °C above dew point to reduce the risk of condensation or blooming on the floor finish.
Substrate Temperature
+10 °C min. / +30 °C max.
Substrate Moisture Content
When performing application work with Sikafloor® MultiDur EB-39, the substrate moisture content must not exceed 4 % pbw measured by Tramex.
Test method: Sika®-Tramex meter, CM - measurement or Oven-dry-method.
No rising moisture according to ASTM (Polyethylene-sheet).
Waiting Time / Overcoating
Before applying Sikafloor®-390 N on Sikafloor®-161 HC allow:
| Substrate temperature | Minimum | Maximum |
| +10 °C | 24 hours | 4 days |
| +20 °C | 12 hours | 2 days |
| +30 °C | 8 hours | 1 day |
Before applying Sikafloor®-390 N on Sikafloor®-390 N allow:
| Substrate temperature | Minimum | Maximum |
| +10 °C | 48 hours | 3 days |
| +20 °C | 30 hours | 2 days |
| +30 °C | 20 hours | 30 hours |
Times are approximate and will be affected by changing ambient conditions particularly temperature and relative humidity.
Applied Product Ready for Use
| Temperature | Foot traffic | Light traffic | Full cure |
| +10 °C | ~ 48 hours | ~ 6 days | ~ 10 days |
| +20 °C | ~ 30 hours | ~ 4 days | ~ 7 days |
| +30 °C | ~ 20 hours | ~ 3 days | ~ 5 days |
For traffic with solid / hard wheeled lift trucks allow 3 weeks curing time.
Consumption
Sikafloor® MultiDur EB-39 system (~ 2–3 mm)
| Coating System | Product | Consumption |
| Primer | 1 × Sikafloor®-161 HC | ~ 0.3–0.5 kg/m² |
| Wearing coat | Sikafloor®-390 N (unfilled) | ~ 1.6 kg/m² |
| Broadcast in excess | Silicon Carbide 0.5–1.0 mm or quartz sand 0.4–0.7 mm | ~ 4–6 kg/m² |
| Top coat | Sikafloor®-390 N + 5 % by weight Thinner C | ~ 0.75–0.85 kg/m² |
CLEANING
Please refer to the Method Statement Sikafloor®‐ Cleaning Regime