Product Data Sheet
Show all documents

Sikadur®-43 HS

Epoxy resin mortar

Sikadur®-43 HS is a 3 parts repair and filling mortar based on a combination of epoxy resins and selected high strength aggregates.

Sikadur®-43 HS is an economical material with the following beneficial properties:
  • Rapid hardening
  • Shrinkage-free hardening
  • High mechanical strengths
  • Hardens even at high humidity
  • High resistance against abrasion, impact and vibration
  • Can be applied onto dry and damp substrates (no standing water)
Find a store
Product Data Sheet
Show all documents

Usage

Sikadur®-43 HS is a high strength material that is used as bedding or underfilling mortar (dry pack) or to repair horizontal concrete surfaces, such as:
  • Industrial floors
  • Kerbstones
  • Bridge bearings
  • Foundation slabs
  • Crane rails
  • Joint arrises in highways
  • Concrete runways
  • Industrial floors
  • Abrasion and impact resistance wearing layers
 

Advantages

Sikadur®-43 HS is an economical material with the following beneficial properties:
  • Rapid hardening
  • Shrinkage-free hardening
  • High mechanical strengths
  • Hardens even at high humidity
  • High resistance against abrasion, impact and vibration
  • Can be applied onto dry and damp substrates (no standing water)

Packaging

22 kg sets (parts A + B + C)

Product Details

Product Information

Shelf Life

12 months from the date of production, if stored in undamaged, original sealed packaging, and if storage conditions are met.

Storage Conditions

Sikadur®-43 HS shall be stored in cool and dry conditions, where it is protected from direct sunlight, rain and water.

Density

Sikadur®-43 HS (parts A + B + C)

~2.1 kg/l (mixed mortar)

Sikadur®-43 HS Primer (parts A + B)

~1.05 kg/l
Technical Information

Compressive Strength

7 days

~95 N/mm² (at +25 °C, 65 % r.h.)

Application

Application Information

Mixing Ratio

Sikadur®-43 HS part A : B : C

2 : 1 : 30 parts by weight 2 : 1 : 19 parts by volume

Sikadur®-43 HS Primer part A : B

2 : 1 parts by weight/volume

Layer Thickness

Max. 50 mm / For large areas 15 mm

Ambient Air Temperature

+5 °C min. / +35 °C max.

Substrate Temperature

+5 °C min./ +35 °C max.

Pot Life

Temperature

10 kg

2 kg

+40 °C

30 minutes

50 minutes

+30 °C

45 minutes

100 minutes

+20 °C

60 minutes

200 minutes
Application steps

SUBSTRATE QUALITY

All surfaces must be clean, free from oil, grease, old coatings, laitance, standing water and all loosely adhering particles. Sandblasting, high pressure water-jetting, grinding or scabbling of substrate is necessary.

SUBSTRATE PREPARATION

Prime with Sikadur®-43 HS Primer for dry substrate. On damp substrates (no standing water) use Sikadur®-31 CF as primer, work well into substrate. Always work wet-on-wet on the bonding bridge/primer.

MIXING

Mix all of Part B (hardener) with all of Part A (resin) for at least 2 minutes with a slow speed electric drill (maximum 500 rpm) until a smooth consistency and streakfree colour is achieved.

Then add all of Part C (aggregates) and continue mixing until a homogeneous mortar is obtained. Use immediately.

CLEANING OF TOOLS

Clean all tools and application equipment with Sika® Colma Cleaner immediately after use. Hardened or cured material can only be mechanically removed.

 

Documents